Page Comparison

...

1. Your key authentication credentials are, by default, stored in a hidden folder named “.ssh.”
   You’ll need to ensure this folder exists in your home directory before creating your key.
   This can be done using Git Bash (for Windows), as shown belowCMD Prompt.

   1. Open the Git Bash application from the Git Extensions CMD Prompt application as shown in the picture below.
      

      Under Git Extensions Tools Tab, click on ‘Git Bash’ and hit enter
      

      Image RemovedImage Added

      
      b. The

      Git Bash terminal

      CMD Prompt opens and should be active within your home directory.
      The title bar of the terminal window will display MINGW64/c/Users/<your-SDC-username>,
      where <your-SDC-username> is your actual SDC user credential.
      

      Image Removed

      c. Use

      Git Bash

      CMD Prompt to check if the .ssh folder already exists in your home directory:
      At the

      $

      prompt, type the following command and then hit enter.

      This will list all objects in your home directory.
      

      Image Removed

      Code Block

      ls -a

      dir

      Image AddedImage Removed

      
      d. Confirm whether you see the .ssh folder listed in the results:

      
      

      
      e. If not found, then create the .ssh folder:
      At the prompt, type the following and then hit enter.

      Code Block
      mkdir .ssh

      f. Confirm the .ssh folder is now created:
      At the prompt, type the following and then hit enter.

      Code Block

      ls -a

      dir

      
      

2. Next, use Git Bash CMD Prompt to generate a new SSH key and store it in the .ssh folder.
   
   a. Generate the key pair:
   At the prompt, type the following command* and then hit enter

   Code Block
   ssh-keygen -t rsa -b 4096 -C "<your-SDC-username@dot.gov>"

   
   *NOTE: Be sure to replace <your-SDC-username@dot.gov> with your SDC email address,
   or other email address/ identifier of your choosing.
   
   b. It will output the following message: “Generating public/private rsa key pair.”
   
   c. It will then ask you where to save the file with the prompt “Enter file in which to save the key:”
   At the prompt, type the following and hit enter.

   Code Block
   C:\Users\<your-SDC-username>\.ssh\id_rsa

   
   d. It will also ask you to enter a passphrase with the following 2 prompts.
   • “Enter passphrase (empty for no passphrase):”
   • “Enter same passphrase again:”
   Hit the Enter key each time (no need to enter anything else) to accept the defaults.
   
   e. The following messages confirm the new SSH key is now stored in the .ssh folder.
   • “Your identification has been saved in C:\Users\<SDCusername>\.ssh\id_rsa.”
   • “Your public key has been saved in C:\Users\<SDCusername>\.ssh\id_rsa.pub.”
   
   NOTE:  Your SSH key pair is comprised of two files, which have been saved under the .ssh folder in your home directory ( C:/Users/<your-SDC-username>/.ssh/ ) .  
   The private identification is saved in the id_rsa file and the public part of the key is saved in the id_rsa.pub file.
   
   

3. You now need to provide the ‘public’ part of this key to GitLab:
In the Git Bash CMD Prompt terminal, type the following command at the prompt, and then hit enter.

...

5. To test whether your SSH key was added correctly, type the following command, in your Git Bash CMD Prompt terminal,
and then hit enter:

...

a. The first time you connect to GitLab via SSH, you will be asked to verify the authenticity
of the GitLab host you are connecting to. Type “yes” to add the SDC internal GitLab to
the list of trusted hosts.

...

b. You should see the “Welcome to GitLab, @SDCusername!” message.
NOTE: Once added to the list of known hosts, you will not be asked to validate the
authenticity of SDC internal GitLab’s host again. Run the above command once more,
and you should only receive a “Welcome to GitLab, @SDCusername!” message.

...